IRRIGAMATIC NET

IRRIGAMATIC series NET can be applied to all self-propelled sprinklers, with turbine, pneurile, with engine or with hydraulic rewinding system. 
- Integrated 4G and lte card for data transmission and reception functions through mobile phone and App, that allows to:
  • Send a Notification when a programmed event takes place (end of work, wind, rain, ...)
  • Check more than 10 parameters of the installation
  • Execute start - stop - change speed commands
- Current date and time;
 
- Measurement of the rolled out and rewound pipe;
 
- Setup the time for work start and finish;
 
- Initial pause from 0 to 120 min;
 
- Working speed adjustment from 1 to 4 sectors (4 to 850 m/h);
 
- Displays the work duration and work end time;
 
- Setup of work end time and automatic adjustment of working settings;
 
- Final pause from 0 to 120 min;
 
- End of the irrigation cycle at a programmed distance (over the crop);
 
- Operations once the irrigation is over;
 
- Automatic switch-off for energy saving;
 
- Possibility of connecting rain and wind sensor;
 
- Possibility of expansion for the control command of the return auxiliary diesel engine (MTR).
 
BY-PASS VALVE ADJUSTMENT
The BY-PASS valve has a special butterfly with an elastic edge allowing it to work even if water
contains foreign bodies.
The motor reduction unit controlled by the console is mounted on the valve shaft.
Preset for flanged connection (1½” - 2” - 2½” - 3” - 4”) and with thread from ( 2” - 2”½” - 3”- 4”).
 
BALL-VALVE ADJUSTMENT LUNG VALVE
For pneurile sprinklers the adjustment is obtained with a ball valve ½” - ¾” and 1”.
The motor reduction unit controlled by the console is mounted on the valve shaft.
 
EPICYCLIC MOTOR REDUCTION UNIT
Epicyclic motor reduction unit for by-pass valve for models up to 3” and 4” HP.
 
MOTOR REDUCTION UNIT
Motor reduction unit for by-pass valve up to 3” and PN.
 
ENGINE ADJUSTMENT
The crank motor reduction unit controlled by the console adjusts the engine accelerator that winds the reel up.
 
HYDRAULIC VALVE ADJUSTMENT
Motor reduction units dedicated to oil flow adjustment on hydraulic sprinklers.
Available in the versions: 180° - 270° - 3 rev. - 5 rev.
SLOW CLOSING STOP
The butterfly valve consists of a cast iron body, with EPDM gasket and stainless steel shaft.
Can be supplied in the following sizes: 2½”- 3” - 4”- 5”.
 
SLOW CLOSING MOTR REDUCTION UNIT
The slow closing motor reduction unit to drive a butterfly up to 3”.
Available in versions closing in 1.5 minutes (To be mounted on the discharge end) or in 4 minutes (to be mounted on the inlet).
 
SLOW CLOSING MOTOR REDUCTION UNIT 4”
Version with supplementary reduction unit for valves 4” to 5” with 4 minutes’operating time.
 
MOTORIZED SHUNT VALVE
A three-way valve used to pilot a hydraulic valve to discharge the pressure from the pipe and stop the irrigation cycle.
Five-way valve available to control a double-acting cylinder.
 
END OF REWINDING SENSOR
It receives a signal at end of rewinding to activate the final pause of the irrigation cycle.
The fixed sensor and the magnet mounted on a mobile part do not need to be in touch.
 
INDUCTIVE SPEED SENSOR
The rewinding speed is measured by the pulses sent by an induction speed sensor detecting the passage of the pignon teeth.
Available with standard range (4 mm) or long range (8 mm).
 
ROLLER
Rubberized it is supplied in various sizes and available in normal version or for pneurile sprinklers.
 
MAGNETIC SPEED SENSOR
Normally available with spiral cable.
 
STAINLESS STEEL CASE
To store and protect the console and a battery 12v-6Ah.
Provided with padlock and inspection window.
 
PHOTOVOLTAIC PANEL
It can be used for all the IRRIGAMATIC models.
The battery 12V is recharged by sun energy. It suppleis a max. power of approx. 4W. Size 40x40 cm.
 
PRESSURE SWITCH
It can be used for all the IRRIGAMATIC models.
It starts and/or stops the irrigation cycle depending on the pressure inside the pipe.
 
MANUAL REGULATOR
Flow rate manual regulator for by-pass valve.
 
RAIN-WIND SENSOR
Capacitive rain sensor and helix wind sensor for Irrigamatic.
 

Monitor for electronic irrigation control